Podpěra vodicího šroubu pro laserové sintrování drylin s kluznými ložisky iglidur, pevné ložisko, pravostranný závit

Bezkorozní ložiska pro trapézové závitové tyče
Ložiska dryspin® s laserovým sintrováním

Praktická ložiska závitových tyčí jsou k dispozici pro závity o velikosti 6 až 24 mm. Možnosti montáže s kluznými ložisky nebo kuličkovými ložisky (BB) s vyšší dynamikou. Všechny podpěry vodicích šroubů jsou dodávány v eloxovaném hliníku, stejně jako odpovídající upínací kroužky.

► Samomazné a bezúdržbové
► Domeček pro podpěru vodicího šroubu
► Otvor pro montáž sestavy
► Bloky ložisek vytvořené laserovým sintrováním jsou k dispozici pro vodicí šrouby o průměru 6–20 mm
► Typy pro závity TR a DS

FB: Pevné ložisko s eloxovaným upínacím kroužkem s pravostranným závitem a samomazným iglidur® pouzdrem
FL: Plovoucí ložisko se samomazným iglidur® pouzdrem
LH: Možnost levostranného závitu, pouze TR10x2, TR10x3, TR18x4 a TR24x5


_________________________________________________________________________________________

Why are there different types?

To determine the application parameters we must consider the position and direction of the forces within the system. To control these forces and ensure correct operation we use fixed and floating bearings the fixed type are used to control the accuracy and the floating bearings are used to allow for misalignment. There are different bearing options, such as the fixed floating bearing and the double-sided floating bearing.


Fixed floating bearing:
The fixed bearing clearly positions the shaft in an axial direction. The fixed bearing must therefore absorb both radial and axial forces and guide them into the surrounding structure. This can basically be done by a single bearing. The floating bearing corrects parallelism errors and offers thermal expansion capability, which means that the cable is not stressed.

Advantages of the fixed floating bearing
► No axial clearance
► Expansion of the shaft (e. g. due to temperature) uncritical
► Suitable for alternating axial loads
► Clarity of the acting forces 


Double-sided floating bearing:
In a double-sided floating bearing arrangement, the lead screw is not clearly fixed in the axial direction. This means that mechanical or thermal changes in length can be absorbed without causing stress on the bearing, however the lead screw is not protected against movement This has to be considered in particular when dealing with positioning applications.

Advantages double-sided floating bearing:
► Cost-effective
► Low design cost
► Expansion of the shaft (e. g. due to temperature) in the range of the clearance uncritical

Disadvantages:
► Not clearly fixed in axial direction
► Not suitable for alternating axial loads
► Only if axial clearance does not cause any functional influence


_________________________________________________________________________________________

Types 

Fixed bearing (FB):
Depending on the thread dimension, this version is clamped in the thread itself or on the outside diameter of the lead screw. For high helix lead screws, it is always the outer diameter that it is clamped to.

► Note: You can also choose a bearing block for your application that uses the measurement d1 for clamping onto the turned machined end.


Floating bearing (FL):
Depending on the lead screw's dimensions, a machined end has to be turned to the value d1. You can see below which dimensions this applies to. The floating bearing block merely supports the lead screw. This type does not prevent the lead screw from drifting.


Ball Bearing Version (BB):
This bearing block should always be used when the application is highly dynamic, such as when using a motor


_________________________________________________________________________________________

Návrh opracování zakončení vodicího šroubu:
 

Objednací číslo	d1 mm
SLS-16x2-LL	12
SLS-16x4-LL	12
SLS-18x4-LL	12
SLS-18x8P4-LL	12
SLS-18x24-LL	12
SLS-18x100-LL	12
SLS-20x4-LL	12
SLS-24x5-LL	14
SLS-S16-LL	12
SLS-S18-LL	12
SLS-S20-LL	12

► Poznámka k maximálnímu zatížení: může přesáhnout maximální zatížení matice vodicího šroubu